1
00:00:23,448 --> 00:00:30,110
In the "Connection & Firmware" tab on the "Preferences" page, the settings for the device connection and "Firmware Update" can be adjusted

2
00:00:30,135 --> 00:00:34,167
Also the settings for the connection can be adjusted in the "Details" section

3
00:00:34,192 --> 00:00:37,155
The "IP" field is used to connect to the device

4
00:00:37,180 --> 00:00:42,925
In the past, the last three digits of the device's serial number were used for the fourth part of this field,

5
00:00:42,950 --> 00:00:50,186
but as of 15/07/2019, the last two digits of the device's serial number are used for this purpose

6
00:00:50,211 --> 00:00:55,302
The "DNS", "Gateway", 'Subset Mask" and "Port" fields are used for network connections

7
00:00:55,327 --> 00:01:02,357
Once connected to the device, you can change these elements and then by selecting the "Set to ATM" option the changes can be saved

8
00:01:02,382 --> 00:01:10,421
The "Serial Number" is not changeable by user and after connecting to the device, the last three digits of the device's serial is written in this part

9
00:01:10,446 --> 00:01:13,480
The "Version" field displays the current version of the device

10
00:01:13,505 --> 00:01:18,311
 and  the "Minimum Version" field displays the minimum version that allows updating the “Firmware"

11
00:01:18,336 --> 00:01:23,049
In the "MAC Address" field, users can use the same software to connect to two devices

12
00:01:23,074 --> 00:01:31,364
If the "MAC Address" of both devices is consists of 6 part  including 2-character is the same, it is necessary to change one of them

13
00:01:31,389 --> 00:01:38,639
Enabling the "Enable Update Connection Date by Device" option causes the information of this part to be refreshed continually

14
00:01:38,664 --> 00:01:42,644
. If the user wishes to make and apply some changes in this section,

15
00:01:42,676 --> 00:01:48,476
, they should uncheck the mentioned option and by clicking on the "Set to AMT" option, apply the changes

16
00:01:48,501 --> 00:01:51,796
The “Connect” bottom is used to connect to the device,

17
00:01:51,820 --> 00:01:56,093
The “Refresh Connection” bottom is used to connect and disconnect the device once,

18
00:01:56,117 --> 00:01:59,159
the “Disconnect” bottom is used to disconnect the deivce,

19
00:01:59,183 --> 00:02:04,989
the “Ping Entered IP” bottom is used to check the authenticity of the connection to the device via LAN.

20
00:02:05,013 --> 00:02:11,331
and, finally, the “Ping Wi-Fi” bottom is used to check the authenticity of the connection to the device via "Wi-Fi"

21
00:02:11,355 --> 00:02:18,227
If the connection is made via LAN, by clicking on the “Ping Entered IP”, the IP which is entered in this section will be pinged.

22
00:02:18,251 --> 00:02:30,023
If the connection is made via Wi-Fi, by clicking on “Ping Wi-Fi”, this IP (192.168.1.1), which is specified for the Wi-Fi of all devices, will be pinged

23
00:02:30,047 --> 00:02:37,188
“Update Firmware” is used to update the firmware of the device which is, usually, done automatically after connecting to the device

24
00:02:37,212 --> 00:02:45,848
 If it didn’t happen automatically, the “Update Firmware in Flash Mode” must be used. How to use this option is explained in the related animation