1
00:00:24,852 --> 00:00:30,986
‪In order to be able to perform various tests with the device, it is necessary to connect to it via a laptop or computer

2
00:00:31,011 --> 00:00:36,005
‪Before starting the device, the earth wire from the back of the device needs to be connected

3
00:00:39,455 --> 00:00:43,743
‪Then, the power cord is connected to the specified location on the back of the device

4
00:00:44,062 --> 00:00:49,567
Note that if the outlet is grounded, there is no need to connect the ground wire from the back of the device

5
00:00:52,462 --> 00:00:58,203
‪After connecting the power cord, the power button on the front of the device is pressed and the device turns on

6
00:00:58,228 --> 00:01:04,425
‪As the device turns on, 8 binary input lights (on the bottom row) and 2 analog DC input lights (on the top right) turn on

7
00:01:04,570 --> 00:01:07,915
‪There are two ways to connect to the device: Wi-Fi and LAN

8
00:01:07,940 --> 00:01:12,504
‪The switch on the back of the device is adjusted according to the type of the connection

9
00:01:12,529 --> 00:01:18,860
‪To switch the LAN connection, one end of the LAN cable is connected to the device and the other end is connected to the laptop

10
00:01:18,885 --> 00:01:28,170
‪When the device and the laptop are properly connected and the switch is changed from Wi-Fi to LAN, the LAN port light of the device and the laptop turn on

11
00:01:29,025 --> 00:01:35,104
‪The setting for the connection of the LAN port is set only once for each computer before the first connection

12
00:01:35,129 --> 00:01:42,201
‪To set these settings, go to the "Control Panel" and open "Network and Sharing Center"

13
00:01:42,719 --> 00:01:47,640
‪On this window, by clicking on "Change Adapter Setting" another window opens

14
00:01:48,213 --> 00:01:54,273
There are several sections on this window. To change the LAN settings, double click on "Ethernet".

15
00:01:54,715 --> 00:02:18,326
Click on “Internet Protocol Version 4” in the opened window. On this window, enter 192.168.1.20 in the "IP Address" field and then close the window.

16
00:02:29,819 --> 00:02:37,255
‪Then, open the "AMPRO" software. By clicking on "Preferences" on the start page of the software, a new window opens

17
00:02:37,760 --> 00:02:45,086
On this window, enter the last three digits of the serial number of the device in the fourth part of the IP field.

18
00:02:45,700 --> 00:02:48,877
‪To connect to the device, click on “CONNECT”

19
00:02:48,902 --> 00:02:58,233
‪If a new version is connected to the device, the "Firmware" of the device will be updated once and after the green bar is filled, the device will be connected in a few seconds

20
00:03:08,351 --> 00:03:14,608
‪To connect via Wi-Fi, the switch on the back of the device needs to be set on “Wi-Fi”

21
00:03:21,977 --> 00:03:28,017
‪Then, from the "Wi-Fi" in quick launch bar on the laptop, find and select the Wi-Fi connection of the device

22
00:03:34,645 --> 00:03:42,253
‪The password for this connection is the serial number available from the label attached to the side of the device

23
00:03:52,553 --> 00:03:58,171
‪Once the connection is complete, click on “Preferences” on the start page of the software

24
00:03:58,196 --> 00:04:07,335
‪On this page, enter the last three digits (for the devices produced after 05/07/2019, the last two digits of the serial number should be entered) of the serial number of the deivce in the fourth part of the "I" field

25
00:04:07,360 --> 00:04:12,259
‪To connect to the device, click on “CONNECT”