1 00:01:02,586 --> 00:01:11,225 ‪In order to remove the device from the suitcase, by pressing the push button, the handle of the device should be placed in a 45 degree angle and taken out of the box 2 00:01:11,875 --> 00:01:19,628 ‪To change the status of handle of the device, it is necessary to press the side buttons of the device simultaneously and then the status should be changed 3 00:01:19,793 --> 00:01:26,659 ‪Once the device is positioned on the intended surface, the handle of the device can be put on the device by pressing the push button 4 00:01:27,694 --> 00:01:33,403 ‪Also, it is possible for the handle to be positioned beneath the device so it could be used as a stand for the device 5 00:01:33,474 --> 00:01:38,819 ‪Moreover, the stands located under the device can be used for this purpose too 6 00:01:39,478 --> 00:01:45,694 ‪At the bottom of the device are the air conditioning grooves and it is crucial to consider that, while positioning the device, 7 00:01:45,742 --> 00:01:49,661 these grooves must not be blocked under any circumstances 8 00:01:50,814 --> 00:01:57,491 The front panel of the device consists of the outputs, inputs, device status lights, and power off/on button 9 00:01:59,153 --> 00:02:05,826 ‪If the green light of the main relay is on, it means that all main switches of the device are on 10 00:02:06,548 --> 00:02:13,768 ‪If the green light of connected is on, it means that the device is correctly connected to the software via PC or mobile phone 11 00:02:15,353 --> 00:02:20,745 ‪If the red light of error is on, it means that there is a problem with the device and it has stopped working 12 00:02:20,770 --> 00:02:26,043 As long as the problem is not resolved, this light will remain on and the device will not work 13 00:02:33,160 --> 00:02:44,785 ‫The two voltage groups A and B allow the user to receive up to 150V AC and 212V DC in all four phases simultaneously with a precision of 10mV 14 00:02:44,810 --> 00:02:52,187 ‪with a maximum current of 0.4A AC and 0.6A DC as well as up to 2A in transient mode 15 00:02:52,212 --> 00:02:58,670 ‪By changing the wiring, it is possible to receive up to 450V single-phase AC from the device 16 00:02:58,765 --> 00:03:05,712 ‪Also, it is possible to increase the output voltage and provide the user with a 150V AC with a maximum current of 17 00:03:05,737 --> 00:03:10,606 0.8A by changing the wiring and paralleling the two current sources 18 00:03:13,585 --> 00:03:22,119 ‪The two current groups A and B allow the user to receive up to 32A in all six phases simultaneously or 64A three-phase 19 00:03:22,144 --> 00:03:28,561 ‪Moreover, by changing the wiring, it is possible to receive up to 128 single-phase amperes from the device 20 00:03:28,609 --> 00:03:35,562 ‪At the “Auxiliary DC” output, a DC voltage as high as 0 to 210V is permanently adjustable 21 00:03:37,323 --> 00:03:39,749 ‪This is where the integrated cable is connected. 22 00:03:39,774 --> 00:03:47,675 The amount of the current and the output voltage of this port are the same as the amounts of the current and voltage ports that have been described earlier 23 00:03:54,831 --> 00:04:05,387 ‪Four binary outputs can be used as a key or for generating digital signals. There are 10amperes relays behind these binaries 24 00:04:05,641 --> 00:04:16,407 ‪The analog inputs of the device are capable of receiving both analog and digital signals. All 8 inputs can be active simultaneously 25 00:04:16,729 --> 00:04:29,247 ‪Other than reading them, these inputs can show the waveform of voltage in three voltage levels of 4.5, 30 and 188V with the precision of 4, 10 and 100mV 26 00:04:31,174 --> 00:04:42,743 ‪The analog DC input section is capable of measuring voltages up to 200mV with a precision of 50µV and current up to 500µA with a precision of 50µA 27 00:04:49,004 --> 00:04:55,625 ‪This port is used to protect the earth connection and the earth cable of the device is connected to this port 28 00:04:57,275 --> 00:05:03,654 ‪In this section, in order to protect the device, a 15A and 250V fuse is used 29 00:05:04,487 --> 00:05:10,758 ‪The power supply port is located here. The power cord of the device is plugged to this port 30 00:05:12,454 --> 00:05:19,871 ‪The RS232 port is mainly used for resetting the IP and updating the firmware 31 00:05:21,379 --> 00:05:27,555 ‪To do this, the RS232 dongle, which is a part of the equipment of the device, needs to be connected to this port. 32 00:05:27,580 --> 00:05:32,118 Then, the necessary operation, described in the animations, needs to be performed. 33 00:05:35,413 --> 00:05:41,600 ‪In this section, by using the switch, the communication protocol between the device and laptop is selected. 34 00:05:41,625 --> 00:05:47,091 If the switch is up, the connection is via Wi-Fi and if the switch is down, the connection is via LAN 35 00:05:47,674 --> 00:05:51,921 ‪The LAN port located under this switch is used for the mentioned communication. 36 00:05:51,946 --> 00:05:56,834 The laptop settings for connecting a laptop to the device are described in the following animations 37 00:05:58,944 --> 00:06:06,238 ‪The GPS antenna, which is used for time synchronization of two devices for performing a longitudinal test, is connected to this part 38 00:06:16,953 --> 00:06:28,128 ‪This glass box includes: one-side-socket one-side-wire lug wire, crocodile clip, 30cm test wire, 10cm test wire, 4mm test socket and cable tie 39 00:06:29,850 --> 00:06:38,038 ‪Other pieces of equipment that come with the device are communication cables which are used for communicating with the relay and injecting voltage or current. 40 00:07:01,163 --> 00:07:09,760 LAN cable: The blue cable, visible in the image, is used to connect the device to a laptop. 41 00:07:11,063 --> 00:07:18,637 ‪Earth cable: The yellow cable is the ground (earth) wire whose place of connection to the device was shown earlier 42 00:07:18,865 --> 00:07:26,932 ‪While one side of this cable is connected to the device, the other side, where the crocodile clip is attached, is connected to the location of the ground connection 43 00:07:30,235 --> 00:07:35,974 ‪The black cable on the right is the power cable and the one on the left is the GPS antenna cable 44 00:07:36,378 --> 00:07:44,060 ‪This antenna is used for End to End tests. The GPS antenna is used for time synchronization of two devices for performing a longitudinal test 45 00:07:47,767 --> 00:07:52,367 ‪Serial dongle This dongle is used to reset the device 46 00:07:53,221 --> 00:08:00,061 ‪The 2nd and 3rd pins of this dongle are interconnected, so if the dongle cannot be accessed, 47 00:08:00,086 --> 00:08:05,820 the device can be reset by connecting the 2nd and 3rd pins to the RS232 port located on the back of the device 48 00:08:08,540 --> 00:08:16,696 ‪Capacitor box In this capacitor set, there are 3 1000μF capacitors which are used as a filter in equipment tests 49 00:08:27,100 --> 00:08:35,724 ‪Integrated or Neutrik cable This cable has 8 output wires on one end and a single part on the other which connects to the device 50 00:08:36,749 --> 00:08:41,799 ‪To plug this cable, first insert the tab of the Neutrik cable as it is shown in the image. 51 00:08:41,824 --> 00:08:47,963 Then, after the Neutrik cable is inserted, spin it to the right until the metal pin is fit into its place 52 00:08:49,209 --> 00:08:56,321 ‪To unplug the Neutrik cable, pull the tab and spin it to the left. After the spin is complete, it can be removed 53 00:08:59,497 --> 00:09:06,935 ‪There are several labels attached to the sides of the device. The first label includes the serial number and technical information of the device 54 00:09:07,136 --> 00:09:12,243 And ‪The second label includes contact information for device support 55 00:09:16,071 --> 00:09:20,701 ‪Trolley: This case is designed for convenient transportation of the device 56 00:09:21,238 --> 00:09:29,910 ‪To place it inside the case, the device must be standing perpendicular to the surface. Then it can be placed in the case and after that the case can be closed 57 00:09:32,083 --> 00:09:37,390 ‪At the front and back of the case there are pockets where the equipment of the device can be placed